In 1975 the X1/9 (the Italian pronunciation of X1/9, ics uno/nove) was chosen by Dallara to enter the World Championship for Makes (in the Group 5 Special Production class). The Dallara Icsunonove featured a modified X1/9 engine with a custom 16v cylinder-head and fundamental suspension and body/monocoque alterations, the most obvious of which are the massively flared wheel-arches and the over-sized rear wing.

A lot of drag in the X1/9 comes off the rear window area. The Dallara rear wing was fixed at the roof line and is intended to ‘clean up’ the air coming off the back window and rear of the car… and not to generate huge down force. Dallara personnel have suggested it was their best guess at the time rather than as the result of lots of wind tunnel testing.

The Dallara X1/9 retained the original passenger compartment, with front and rear space frames extended from the bulkheads to mount engine/box and suspension components. The initial Dallaras were built to Group 5 racing regulations.

Almost every part of the car was redesigned with one goal: to outperform the opposition. Heart of the project was the 4 valve/cylinder fuel injected engine that in the 1300 cc version produced an astonishing 192bhp@9700rpm, while the 1600 cc had ~210bhp@~1000rpm less.

This was a silhouette formula allowing for maximum mechanical and weight reduction mods. – yet keeping the car’s production body outline. Few production components remained. To reduce weight, suspension uprights were cast from magnesium alloy, lower suspension arms were specially fabricated including lightweight radius arms.

The fuel tank was re-located in front of the front bulkhead along with the brake and clutch master cylinders. In the earliest versions, the wing panels were retained – although now made of lightweight glass fibre. (In other words they didn’t make one-piece front or rear clamshells). Dallara achieved around 260 kg weight savings over standard.

Характеристики изображения:

  • Разрешение: 640×480 @ 72×72 DPI 22,58×16,93cm
  • Размер: 151.52 KB
  • Добавил: MG , 19 лет назад
  • Статус изображения: Принято

Все изображения являются чьей-либо собственностью.

Если вы считаете, что пользователи сайта ошиблись, разместив данную картинку в этом разделе, то было бы здорово, если бы вы написали об этом в комментариях и указали на ошибку.

Поделиться своей радостью, обсудить наболевшее и просто поболтать об автомобилях и не только вы можете на нашем форуме.

Комментарии

19 лет назад
MG

1975 Fiat X1/9 Dallara (Bertone)

18 лет назад
MG

дизайн Bertone

18 лет назад
Автоманьяк

"Первый Dallaras используется Fiat в блок с 1300cc в доме разработан 16-клапан голову. Mechanical fuel injection was available very shortly afterwards. Механические впрыска топлива и была доступна в самое ближайшее время после них. This layout gave around 192bhp at 9700rpm. Этот формат дает около 192bhp на 9700rpm.

Later 1600cc variants achieved over 200bhp with improved torque. Позже 1600cc варианты, достигнутые за 200bhp с улучшенными крутящего момента. Reliability proved to be a challenge though. Надежность оказалась задача хотя и.

The look of the engines was very different to the 16 valve designs from Abarth and Fiat/ Lancia at the time. Вид двигателей весьма отличается от 16 клапана конструкций из Abarth и Fiat / Lancia на время.

В 1980 году этот автомобиль был гонки с одним куском перед грейфером, "stroked" Фиат 1500cc двигатель с Cosworth поршни, клапана 16-Dallara головой, двумя 45 мм Вебер carbs, давая 184bhp и весом, по крайней вокруг 600kg "

- это Google так переводит с английского))))))

-1

Чтобы иметь возможность оставлять комментарии, необходимо зарегистрироваться или войти на сайт с помощью учётной записи в одной из социальных сетей

AutoWP.ru '2005–н.в.